| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: hisilicon/qm - request reserved interrupt for virtual function
The device interrupt vector 3 is an error interrupt for
physical function and a reserved interrupt for virtual function.
However, the driver has not registered the reserved interrupt for
virtual function. When allocating interrupts, the number of interrupts
is allocated based on powers of two, which includes this interrupt.
When the system enables GICv4 and the virtual function passthrough
to the virtual machine, releasing the interrupt in the driver
triggers a warning.
The WARNING report is:
WARNING: CPU: 62 PID: 14889 at arch/arm64/kvm/vgic/vgic-its.c:852 its_free_ite+0x94/0xb4
Therefore, register a reserved interrupt for VF and set the
IRQF_NO_AUTOEN flag to avoid that warning. |
| In the Linux kernel, the following vulnerability has been resolved:
net/9p: Fix buffer overflow in USB transport layer
A buffer overflow vulnerability exists in the USB 9pfs transport layer
where inconsistent size validation between packet header parsing and
actual data copying allows a malicious USB host to overflow heap buffers.
The issue occurs because:
- usb9pfs_rx_header() validates only the declared size in packet header
- usb9pfs_rx_complete() uses req->actual (actual received bytes) for
memcpy
This allows an attacker to craft packets with small declared size
(bypassing validation) but large actual payload (triggering overflow
in memcpy).
Add validation in usb9pfs_rx_complete() to ensure req->actual does not
exceed the buffer capacity before copying data. |
| In the Linux kernel, the following vulnerability has been resolved:
thunderbolt: Fix use-after-free in tb_dp_dprx_work
The original code relies on cancel_delayed_work() in tb_dp_dprx_stop(),
which does not ensure that the delayed work item tunnel->dprx_work has
fully completed if it was already running. This leads to use-after-free
scenarios where tb_tunnel is deallocated by tb_tunnel_put(), while
tunnel->dprx_work remains active and attempts to dereference tb_tunnel
in tb_dp_dprx_work().
A typical race condition is illustrated below:
CPU 0 | CPU 1
tb_dp_tunnel_active() |
tb_deactivate_and_free_tunnel()| tb_dp_dprx_start()
tb_tunnel_deactivate() | queue_delayed_work()
tb_dp_activate() |
tb_dp_dprx_stop() | tb_dp_dprx_work() //delayed worker
cancel_delayed_work() |
tb_tunnel_put(tunnel); |
| tunnel = container_of(...); //UAF
| tunnel-> //UAF
Replacing cancel_delayed_work() with cancel_delayed_work_sync() is
not feasible as it would introduce a deadlock: both tb_dp_dprx_work()
and the cleanup path acquire tb->lock, and cancel_delayed_work_sync()
would wait indefinitely for the work item that cannot proceed.
Instead, implement proper reference counting:
- If cancel_delayed_work() returns true (work is pending), we release
the reference in the stop function.
- If it returns false (work is executing or already completed), the
reference is released in delayed work function itself.
This ensures the tb_tunnel remains valid during work item execution
while preventing memory leaks.
This bug was found by static analysis. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix to do sanity check on node footer for non inode dnode
As syzbot reported below:
------------[ cut here ]------------
kernel BUG at fs/f2fs/file.c:1243!
Oops: invalid opcode: 0000 [#1] SMP KASAN NOPTI
CPU: 0 UID: 0 PID: 5354 Comm: syz.0.0 Not tainted 6.17.0-rc1-syzkaller-00211-g90d970cade8e #0 PREEMPT(full)
RIP: 0010:f2fs_truncate_hole+0x69e/0x6c0 fs/f2fs/file.c:1243
Call Trace:
<TASK>
f2fs_punch_hole+0x2db/0x330 fs/f2fs/file.c:1306
f2fs_fallocate+0x546/0x990 fs/f2fs/file.c:2018
vfs_fallocate+0x666/0x7e0 fs/open.c:342
ksys_fallocate fs/open.c:366 [inline]
__do_sys_fallocate fs/open.c:371 [inline]
__se_sys_fallocate fs/open.c:369 [inline]
__x64_sys_fallocate+0xc0/0x110 fs/open.c:369
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7f1e65f8ebe9
w/ a fuzzed image, f2fs may encounter panic due to it detects inconsistent
truncation range in direct node in f2fs_truncate_hole().
The root cause is: a non-inode dnode may has the same footer.ino and
footer.nid, so the dnode will be parsed as an inode, then ADDRS_PER_PAGE()
may return wrong blkaddr count which may be 923 typically, by chance,
dn.ofs_in_node is equal to 923, then count can be calculated to 0 in below
statement, later it will trigger panic w/ f2fs_bug_on(, count == 0 || ...).
count = min(end_offset - dn.ofs_in_node, pg_end - pg_start);
This patch introduces a new node_type NODE_TYPE_NON_INODE, then allowing
passing the new_type to sanity_check_node_footer in f2fs_get_node_folio()
to detect corruption that a non-inode dnode has the same footer.ino and
footer.nid.
Scripts to reproduce:
mkfs.f2fs -f /dev/vdb
mount /dev/vdb /mnt/f2fs
touch /mnt/f2fs/foo
touch /mnt/f2fs/bar
dd if=/dev/zero of=/mnt/f2fs/foo bs=1M count=8
umount /mnt/f2fs
inject.f2fs --node --mb i_nid --nid 4 --idx 0 --val 5 /dev/vdb
mount /dev/vdb /mnt/f2fs
xfs_io /mnt/f2fs/foo -c "fpunch 6984k 4k" |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/vt-d: Disallow dirty tracking if incoherent page walk
Dirty page tracking relies on the IOMMU atomically updating the dirty bit
in the paging-structure entry. For this operation to succeed, the paging-
structure memory must be coherent between the IOMMU and the CPU. In
another word, if the iommu page walk is incoherent, dirty page tracking
doesn't work.
The Intel VT-d specification, Section 3.10 "Snoop Behavior" states:
"Remapping hardware encountering the need to atomically update A/EA/D bits
in a paging-structure entry that is not snooped will result in a non-
recoverable fault."
To prevent an IOMMU from being incorrectly configured for dirty page
tracking when it is operating in an incoherent mode, mark SSADS as
supported only when both ecap_slads and ecap_smpwc are supported. |
| In the Linux kernel, the following vulnerability has been resolved:
media: af9005: Fix null-ptr-deref in af9005_i2c_xfer
In af9005_i2c_xfer, msg is controlled by user. When msg[i].buf
is null and msg[i].len is zero, former checks on msg[i].buf would be
passed. Malicious data finally reach af9005_i2c_xfer. If accessing
msg[i].buf[0] without sanity check, null ptr deref would happen.
We add check on msg[i].len to prevent crash.
Similar commit:
commit 0ed554fd769a
("media: dvb-usb: az6027: fix null-ptr-deref in az6027_i2c_xfer()") |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: comp - Use same definition of context alloc and free ops
In commit 42d9f6c77479 ("crypto: acomp - Move scomp stream allocation
code into acomp"), the crypto_acomp_streams struct was made to rely on
having the alloc_ctx and free_ctx operations defined in the same order
as the scomp_alg struct. But in that same commit, the alloc_ctx and
free_ctx members of scomp_alg may be randomized by structure layout
randomization, since they are contained in a pure ops structure
(containing only function pointers). If the pointers within scomp_alg
are randomized, but those in crypto_acomp_streams are not, then
the order may no longer match. This fixes the problem by removing the
union from scomp_alg so that both crypto_acomp_streams and scomp_alg
will share the same definition of alloc_ctx and free_ctx, ensuring
they will always have the same layout. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Explicitly check accesses to bpf_sock_addr
Syzkaller found a kernel warning on the following sock_addr program:
0: r0 = 0
1: r2 = *(u32 *)(r1 +60)
2: exit
which triggers:
verifier bug: error during ctx access conversion (0)
This is happening because offset 60 in bpf_sock_addr corresponds to an
implicit padding of 4 bytes, right after msg_src_ip4. Access to this
padding isn't rejected in sock_addr_is_valid_access and it thus later
fails to convert the access.
This patch fixes it by explicitly checking the various fields of
bpf_sock_addr in sock_addr_is_valid_access.
I checked the other ctx structures and is_valid_access functions and
didn't find any other similar cases. Other cases of (properly handled)
padding are covered in new tests in a subsequent patch. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/sched: Fix potential double free in drm_sched_job_add_resv_dependencies
When adding dependencies with drm_sched_job_add_dependency(), that
function consumes the fence reference both on success and failure, so in
the latter case the dma_fence_put() on the error path (xarray failed to
expand) is a double free.
Interestingly this bug appears to have been present ever since
commit ebd5f74255b9 ("drm/sched: Add dependency tracking"), since the code
back then looked like this:
drm_sched_job_add_implicit_dependencies():
...
for (i = 0; i < fence_count; i++) {
ret = drm_sched_job_add_dependency(job, fences[i]);
if (ret)
break;
}
for (; i < fence_count; i++)
dma_fence_put(fences[i]);
Which means for the failing 'i' the dma_fence_put was already a double
free. Possibly there were no users at that time, or the test cases were
insufficient to hit it.
The bug was then only noticed and fixed after
commit 9c2ba265352a ("drm/scheduler: use new iterator in drm_sched_job_add_implicit_dependencies v2")
landed, with its fixup of
commit 4eaf02d6076c ("drm/scheduler: fix drm_sched_job_add_implicit_dependencies").
At that point it was a slightly different flavour of a double free, which
commit 963d0b356935 ("drm/scheduler: fix drm_sched_job_add_implicit_dependencies harder")
noticed and attempted to fix.
But it only moved the double free from happening inside the
drm_sched_job_add_dependency(), when releasing the reference not yet
obtained, to the caller, when releasing the reference already released by
the former in the failure case.
As such it is not easy to identify the right target for the fixes tag so
lets keep it simple and just continue the chain.
While fixing we also improve the comment and explain the reason for taking
the reference and not dropping it. |
| In the Linux kernel, the following vulnerability has been resolved:
ixgbevf: fix mailbox API compatibility by negotiating supported features
There was backward compatibility in the terms of mailbox API. Various
drivers from various OSes supporting 10G adapters from Intel portfolio
could easily negotiate mailbox API.
This convention has been broken since introducing API 1.4.
Commit 0062e7cc955e ("ixgbevf: add VF IPsec offload code") added support
for IPSec which is specific only for the kernel ixgbe driver. None of the
rest of the Intel 10G PF/VF drivers supports it. And actually lack of
support was not included in the IPSec implementation - there were no such
code paths. No possibility to negotiate support for the feature was
introduced along with introduction of the feature itself.
Commit 339f28964147 ("ixgbevf: Add support for new mailbox communication
between PF and VF") increasing API version to 1.5 did the same - it
introduced code supported specifically by the PF ESX driver. It altered API
version for the VF driver in the same time not touching the version
defined for the PF ixgbe driver. It led to additional discrepancies,
as the code provided within API 1.6 cannot be supported for Linux ixgbe
driver as it causes crashes.
The issue was noticed some time ago and mitigated by Jake within the commit
d0725312adf5 ("ixgbevf: stop attempting IPSEC offload on Mailbox API 1.5").
As a result we have regression for IPsec support and after increasing API
to version 1.6 ixgbevf driver stopped to support ESX MBX.
To fix this mess add new mailbox op asking PF driver about supported
features. Basing on a response determine whether to set support for IPSec
and ESX-specific enhanced mailbox.
New mailbox op, for compatibility purposes, must be added within new API
revision, as API version of OOT PF & VF drivers is already increased to
1.6 and doesn't incorporate features negotiate op.
Features negotiation mechanism gives possibility to be extended with new
features when needed in the future. |
| In the Linux kernel, the following vulnerability has been resolved:
powerpc/powernv/sriov: perform null check on iov before dereferencing iov
Currently pointer iov is being dereferenced before the null check of iov
which can lead to null pointer dereference errors. Fix this by moving the
iov null check before the dereferencing.
Detected using cppcheck static analysis:
linux/arch/powerpc/platforms/powernv/pci-sriov.c:597:12: warning: Either
the condition '!iov' is redundant or there is possible null pointer
dereference: iov. [nullPointerRedundantCheck]
num_vfs = iov->num_vfs;
^ |
| In the Linux kernel, the following vulnerability has been resolved:
dm flakey: don't corrupt the zero page
When we need to zero some range on a block device, the function
__blkdev_issue_zero_pages submits a write bio with the bio vector pointing
to the zero page. If we use dm-flakey with corrupt bio writes option, it
will corrupt the content of the zero page which results in crashes of
various userspace programs. Glibc assumes that memory returned by mmap is
zeroed and it uses it for calloc implementation; if the newly mapped
memory is not zeroed, calloc will return non-zeroed memory.
Fix this bug by testing if the page is equal to ZERO_PAGE(0) and
avoiding the corruption in this case. |
| In the Linux kernel, the following vulnerability has been resolved:
vfs: Don't leak disconnected dentries on umount
When user calls open_by_handle_at() on some inode that is not cached, we
will create disconnected dentry for it. If such dentry is a directory,
exportfs_decode_fh_raw() will then try to connect this dentry to the
dentry tree through reconnect_path(). It may happen for various reasons
(such as corrupted fs or race with rename) that the call to
lookup_one_unlocked() in reconnect_one() will fail to find the dentry we
are trying to reconnect and instead create a new dentry under the
parent. Now this dentry will not be marked as disconnected although the
parent still may well be disconnected (at least in case this
inconsistency happened because the fs is corrupted and .. doesn't point
to the real parent directory). This creates inconsistency in
disconnected flags but AFAICS it was mostly harmless. At least until
commit f1ee616214cb ("VFS: don't keep disconnected dentries on d_anon")
which removed adding of most disconnected dentries to sb->s_anon list.
Thus after this commit cleanup of disconnected dentries implicitely
relies on the fact that dput() will immediately reclaim such dentries.
However when some leaf dentry isn't marked as disconnected, as in the
scenario described above, the reclaim doesn't happen and the dentries
are "leaked". Memory reclaim can eventually reclaim them but otherwise
they stay in memory and if umount comes first, we hit infamous "Busy
inodes after unmount" bug. Make sure all dentries created under a
disconnected parent are marked as disconnected as well. |
| In the Linux kernel, the following vulnerability has been resolved:
can: hi311x: fix null pointer dereference when resuming from sleep before interface was enabled
This issue is similar to the vulnerability in the `mcp251x` driver,
which was fixed in commit 03c427147b2d ("can: mcp251x: fix resume from
sleep before interface was brought up").
In the `hi311x` driver, when the device resumes from sleep, the driver
schedules `priv->restart_work`. However, if the network interface was
not previously enabled, the `priv->wq` (workqueue) is not allocated and
initialized, leading to a null pointer dereference.
To fix this, we move the allocation and initialization of the workqueue
from the `hi3110_open` function to the `hi3110_can_probe` function.
This ensures that the workqueue is properly initialized before it is
used during device resume. And added logic to destroy the workqueue
in the error handling paths of `hi3110_can_probe` and in the
`hi3110_can_remove` function to prevent resource leaks. |
| In the Linux kernel, the following vulnerability has been resolved:
sparc: fix accurate exception reporting in copy_{from_to}_user for UltraSPARC III
Anthony Yznaga tracked down that a BUG_ON in ext4 code with large folios
enabled resulted from copy_from_user() returning impossibly large values
greater than the size to be copied. This lead to __copy_from_iter()
returning impossible values instead of the actual number of bytes it was
able to copy.
The BUG_ON has been reported in
https://lore.kernel.org/r/b14f55642207e63e907965e209f6323a0df6dcee.camel@physik.fu-berlin.de
The referenced commit introduced exception handlers on user-space memory
references in copy_from_user and copy_to_user. These handlers return from
the respective function and calculate the remaining bytes left to copy
using the current register contents. The exception handlers expect that
%o2 has already been masked during the bulk copy loop, but the masking was
performed after that loop. This will fix the return value of copy_from_user
and copy_to_user in the faulting case. The behaviour of memcpy stays
unchanged. |
| In the Linux kernel, the following vulnerability has been resolved:
blk-mq: check kobject state_in_sysfs before deleting in blk_mq_unregister_hctx
In __blk_mq_update_nr_hw_queues() the return value of
blk_mq_sysfs_register_hctxs() is not checked. If sysfs creation for hctx
fails, later changing the number of hw_queues or removing disk will
trigger the following warning:
kernfs: can not remove 'nr_tags', no directory
WARNING: CPU: 2 PID: 637 at fs/kernfs/dir.c:1707 kernfs_remove_by_name_ns+0x13f/0x160
Call Trace:
remove_files.isra.1+0x38/0xb0
sysfs_remove_group+0x4d/0x100
sysfs_remove_groups+0x31/0x60
__kobject_del+0x23/0xf0
kobject_del+0x17/0x40
blk_mq_unregister_hctx+0x5d/0x80
blk_mq_sysfs_unregister_hctxs+0x94/0xd0
blk_mq_update_nr_hw_queues+0x124/0x760
nullb_update_nr_hw_queues+0x71/0xf0 [null_blk]
nullb_device_submit_queues_store+0x92/0x120 [null_blk]
kobjct_del() was called unconditionally even if sysfs creation failed.
Fix it by checkig the kobject creation statusbefore deleting it. |
| In the Linux kernel, the following vulnerability has been resolved:
net/smc: use smc_lgr_list.lock to protect smc_lgr_list.list iterate in smcr_port_add
While doing smcr_port_add, there maybe linkgroup add into or delete
from smc_lgr_list.list at the same time, which may result kernel crash.
So, use smc_lgr_list.lock to protect smc_lgr_list.list iterate in
smcr_port_add.
The crash calltrace show below:
BUG: kernel NULL pointer dereference, address: 0000000000000000
PGD 0 P4D 0
Oops: 0000 [#1] SMP NOPTI
CPU: 0 PID: 559726 Comm: kworker/0:92 Kdump: loaded Tainted: G
Hardware name: Alibaba Cloud Alibaba Cloud ECS, BIOS 449e491 04/01/2014
Workqueue: events smc_ib_port_event_work [smc]
RIP: 0010:smcr_port_add+0xa6/0xf0 [smc]
RSP: 0000:ffffa5a2c8f67de0 EFLAGS: 00010297
RAX: 0000000000000001 RBX: ffff9935e0650000 RCX: 0000000000000000
RDX: 0000000000000010 RSI: ffff9935e0654290 RDI: ffff9935c8560000
RBP: 0000000000000000 R08: 0000000000000000 R09: ffff9934c0401918
R10: 0000000000000000 R11: ffffffffb4a5c278 R12: ffff99364029aae4
R13: ffff99364029aa00 R14: 00000000ffffffed R15: ffff99364029ab08
FS: 0000000000000000(0000) GS:ffff994380600000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 0000000f06a10003 CR4: 0000000002770ef0
PKRU: 55555554
Call Trace:
smc_ib_port_event_work+0x18f/0x380 [smc]
process_one_work+0x19b/0x340
worker_thread+0x30/0x370
? process_one_work+0x340/0x340
kthread+0x114/0x130
? __kthread_cancel_work+0x50/0x50
ret_from_fork+0x1f/0x30 |
| In the Linux kernel, the following vulnerability has been resolved:
refscale: Fix uninitalized use of wait_queue_head_t
Running the refscale test occasionally crashes the kernel with the
following error:
[ 8569.952896] BUG: unable to handle page fault for address: ffffffffffffffe8
[ 8569.952900] #PF: supervisor read access in kernel mode
[ 8569.952902] #PF: error_code(0x0000) - not-present page
[ 8569.952904] PGD c4b048067 P4D c4b049067 PUD c4b04b067 PMD 0
[ 8569.952910] Oops: 0000 [#1] PREEMPT_RT SMP NOPTI
[ 8569.952916] Hardware name: Dell Inc. PowerEdge R750/0WMWCR, BIOS 1.2.4 05/28/2021
[ 8569.952917] RIP: 0010:prepare_to_wait_event+0x101/0x190
:
[ 8569.952940] Call Trace:
[ 8569.952941] <TASK>
[ 8569.952944] ref_scale_reader+0x380/0x4a0 [refscale]
[ 8569.952959] kthread+0x10e/0x130
[ 8569.952966] ret_from_fork+0x1f/0x30
[ 8569.952973] </TASK>
The likely cause is that init_waitqueue_head() is called after the call to
the torture_create_kthread() function that creates the ref_scale_reader
kthread. Although this init_waitqueue_head() call will very likely
complete before this kthread is created and starts running, it is
possible that the calling kthread will be delayed between the calls to
torture_create_kthread() and init_waitqueue_head(). In this case, the
new kthread will use the waitqueue head before it is properly initialized,
which is not good for the kernel's health and well-being.
The above crash happened here:
static inline void __add_wait_queue(...)
{
:
if (!(wq->flags & WQ_FLAG_PRIORITY)) <=== Crash here
The offset of flags from list_head entry in wait_queue_entry is
-0x18. If reader_tasks[i].wq.head.next is NULL as allocated reader_task
structure is zero initialized, the instruction will try to access address
0xffffffffffffffe8, which is exactly the fault address listed above.
This commit therefore invokes init_waitqueue_head() before creating
the kthread. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Enforce expected_attach_type for tailcall compatibility
Yinhao et al. recently reported:
Our fuzzer tool discovered an uninitialized pointer issue in the
bpf_prog_test_run_xdp() function within the Linux kernel's BPF subsystem.
This leads to a NULL pointer dereference when a BPF program attempts to
deference the txq member of struct xdp_buff object.
The test initializes two programs of BPF_PROG_TYPE_XDP: progA acts as the
entry point for bpf_prog_test_run_xdp() and its expected_attach_type can
neither be of be BPF_XDP_DEVMAP nor BPF_XDP_CPUMAP. progA calls into a slot
of a tailcall map it owns. progB's expected_attach_type must be BPF_XDP_DEVMAP
to pass xdp_is_valid_access() validation. The program returns struct xdp_md's
egress_ifindex, and the latter is only allowed to be accessed under mentioned
expected_attach_type. progB is then inserted into the tailcall which progA
calls.
The underlying issue goes beyond XDP though. Another example are programs
of type BPF_PROG_TYPE_CGROUP_SOCK_ADDR. sock_addr_is_valid_access() as well
as sock_addr_func_proto() have different logic depending on the programs'
expected_attach_type. Similarly, a program attached to BPF_CGROUP_INET4_GETPEERNAME
should not be allowed doing a tailcall into a program which calls bpf_bind()
out of BPF which is only enabled for BPF_CGROUP_INET4_CONNECT.
In short, specifying expected_attach_type allows to open up additional
functionality or restrictions beyond what the basic bpf_prog_type enables.
The use of tailcalls must not violate these constraints. Fix it by enforcing
expected_attach_type in __bpf_prog_map_compatible().
Note that we only enforce this for tailcall maps, but not for BPF devmaps or
cpumaps: There, the programs are invoked through dev_map_bpf_prog_run*() and
cpu_map_bpf_prog_run*() which set up a new environment / context and therefore
these situations are not prone to this issue. |
| In the Linux kernel, the following vulnerability has been resolved:
blk-cgroup: dropping parent refcount after pd_free_fn() is done
Some cgroup policies will access parent pd through child pd even
after pd_offline_fn() is done. If pd_free_fn() for parent is called
before child, then UAF can be triggered. Hence it's better to guarantee
the order of pd_free_fn().
Currently refcount of parent blkg is dropped in __blkg_release(), which
is before pd_free_fn() is called in blkg_free_work_fn() while
blkg_free_work_fn() is called asynchronously.
This patch make sure pd_free_fn() called from removing cgroup is ordered
by delaying dropping parent refcount after calling pd_free_fn() for
child.
BTW, pd_free_fn() will also be called from blkcg_deactivate_policy()
from deleting device, and following patches will guarantee the order. |
