| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
blk-mq: fix blk_mq_tags double free while nr_requests grown
In the case user trigger tags grow by queue sysfs attribute nr_requests,
hctx->sched_tags will be freed directly and replaced with a new
allocated tags, see blk_mq_tag_update_depth().
The problem is that hctx->sched_tags is from elevator->et->tags, while
et->tags is still the freed tags, hence later elevator exit will try to
free the tags again, causing kernel panic.
Fix this problem by replacing et->tags with new allocated tags as well.
Noted there are still some long term problems that will require some
refactor to be fixed thoroughly[1].
[1] https://lore.kernel.org/all/20250815080216.410665-1-yukuai1@huaweicloud.com/ |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtl8xxxu: Fix memory leaks with RTL8723BU, RTL8192EU
The wifi + bluetooth combo chip RTL8723BU can leak memory (especially?)
when it's connected to a bluetooth audio device. The busy bluetooth
traffic generates lots of C2H (card to host) messages, which are not
freed correctly.
To fix this, move the dev_kfree_skb() call in rtl8xxxu_c2hcmd_callback()
inside the loop where skb_dequeue() is called.
The RTL8192EU leaks memory because the C2H messages are added to the
queue and left there forever. (This was fine in the past because it
probably wasn't sending any C2H messages until commit e542e66b7c2e
("wifi: rtl8xxxu: gen2: Turn on the rate control"). Since that commit
it sends a C2H message when the TX rate changes.)
To fix this, delete the check for rf_paths > 1 and the goto. Let the
function process the C2H messages from RTL8192EU like the ones from
the other chips.
Theoretically the RTL8188FU could also leak like RTL8723BU, but it
most likely doesn't send C2H messages frequently enough.
This change was tested with RTL8723BU by Erhard F. I tested it with
RTL8188FU and RTL8192EU. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: mvsas: Fix use-after-free bugs in mvs_work_queue
During the detaching of Marvell's SAS/SATA controller, the original code
calls cancel_delayed_work() in mvs_free() to cancel the delayed work
item mwq->work_q. However, if mwq->work_q is already running, the
cancel_delayed_work() may fail to cancel it. This can lead to
use-after-free scenarios where mvs_free() frees the mvs_info while
mvs_work_queue() is still executing and attempts to access the
already-freed mvs_info.
A typical race condition is illustrated below:
CPU 0 (remove) | CPU 1 (delayed work callback)
mvs_pci_remove() |
mvs_free() | mvs_work_queue()
cancel_delayed_work() |
kfree(mvi) |
| mvi-> // UAF
Replace cancel_delayed_work() with cancel_delayed_work_sync() to ensure
that the delayed work item is properly canceled and any executing
delayed work item completes before the mvs_info is deallocated.
This bug was found by static analysis. |
| In the Linux kernel, the following vulnerability has been resolved:
iommufd: Make sure to zero vfio_iommu_type1_info before copying to user
Missed a zero initialization here. Most of the struct is filled with
a copy_from_user(), however minsz for that copy is smaller than the
actual struct by 8 bytes, thus we don't fill the padding. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: fix a memory leak in the LRU and LRU_PERCPU hash maps
The LRU and LRU_PERCPU maps allocate a new element on update before locking the
target hash table bucket. Right after that the maps try to lock the bucket.
If this fails, then maps return -EBUSY to the caller without releasing the
allocated element. This makes the element untracked: it doesn't belong to
either of free lists, and it doesn't belong to the hash table, so can't be
re-used; this eventually leads to the permanent -ENOMEM on LRU map updates,
which is unexpected. Fix this by returning the element to the local free list
if bucket locking fails. |
| In the Linux kernel, the following vulnerability has been resolved:
RISC-V: kexec: Fix memory leak of fdt buffer
This is reported by kmemleak detector:
unreferenced object 0xff60000082864000 (size 9588):
comm "kexec", pid 146, jiffies 4294900634 (age 64.788s)
hex dump (first 32 bytes):
d0 0d fe ed 00 00 12 ed 00 00 00 48 00 00 11 40 ...........H...@
00 00 00 28 00 00 00 11 00 00 00 02 00 00 00 00 ...(............
backtrace:
[<00000000f95b17c4>] kmemleak_alloc+0x34/0x3e
[<00000000b9ec8e3e>] kmalloc_order+0x9c/0xc4
[<00000000a95cf02e>] kmalloc_order_trace+0x34/0xb6
[<00000000f01e68b4>] __kmalloc+0x5c2/0x62a
[<000000002bd497b2>] kvmalloc_node+0x66/0xd6
[<00000000906542fa>] of_kexec_alloc_and_setup_fdt+0xa6/0x6ea
[<00000000e1166bde>] elf_kexec_load+0x206/0x4ec
[<0000000036548e09>] kexec_image_load_default+0x40/0x4c
[<0000000079fbe1b4>] sys_kexec_file_load+0x1c4/0x322
[<0000000040c62c03>] ret_from_syscall+0x0/0x2
In elf_kexec_load(), a buffer is allocated via kvmalloc() to store fdt.
While it's not freed back to system when kexec kernel is reloaded or
unloaded. Then memory leak is caused. Fix it by introducing riscv
specific function arch_kimage_file_post_load_cleanup(), and freeing the
buffer there. |
| In the Linux kernel, the following vulnerability has been resolved:
mm: swap: check for stable address space before operating on the VMA
It is possible to hit a zero entry while traversing the vmas in unuse_mm()
called from swapoff path and accessing it causes the OOPS:
Unable to handle kernel NULL pointer dereference at virtual address
0000000000000446--> Loading the memory from offset 0x40 on the
XA_ZERO_ENTRY as address.
Mem abort info:
ESR = 0x0000000096000005
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x05: level 1 translation fault
The issue is manifested from the below race between the fork() on a
process and swapoff:
fork(dup_mmap()) swapoff(unuse_mm)
--------------- -----------------
1) Identical mtree is built using
__mt_dup().
2) copy_pte_range()-->
copy_nonpresent_pte():
The dst mm is added into the
mmlist to be visible to the
swapoff operation.
3) Fatal signal is sent to the parent
process(which is the current during the
fork) thus skip the duplication of the
vmas and mark the vma range with
XA_ZERO_ENTRY as a marker for this process
that helps during exit_mmap().
4) swapoff is tried on the
'mm' added to the 'mmlist' as
part of the 2.
5) unuse_mm(), that iterates
through the vma's of this 'mm'
will hit the non-NULL zero entry
and operating on this zero entry
as a vma is resulting into the
oops.
The proper fix would be around not exposing this partially-valid tree to
others when droping the mmap lock, which is being solved with [1]. A
simpler solution would be checking for MMF_UNSTABLE, as it is set if
mm_struct is not fully initialized in dup_mmap().
Thanks to Liam/Lorenzo/David for all the suggestions in fixing this
issue. |
| In the Linux kernel, the following vulnerability has been resolved:
cpufreq: intel_pstate: Fix object lifecycle issue in update_qos_request()
The cpufreq_cpu_put() call in update_qos_request() takes place too early
because the latter subsequently calls freq_qos_update_request() that
indirectly accesses the policy object in question through the QoS request
object passed to it.
Fortunately, update_qos_request() is called under intel_pstate_driver_lock,
so this issue does not matter for changing the intel_pstate operation
mode, but it theoretically can cause a crash to occur on CPU device hot
removal (which currently can only happen in virt, but it is formally
supported nevertheless).
Address this issue by modifying update_qos_request() to drop the
reference to the policy later. |
| In the Linux kernel, the following vulnerability has been resolved:
io-wq: Fix memory leak in worker creation
If the CPU mask allocation for a node fails, then the memory allocated for
the 'io_wqe' struct of the current node doesn't get freed on the error
handling path, since it has not yet been added to the 'wqes' array.
This was spotted when fuzzing v6.1-rc1 with Syzkaller:
BUG: memory leak
unreferenced object 0xffff8880093d5000 (size 1024):
comm "syz-executor.2", pid 7701, jiffies 4295048595 (age 13.900s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<00000000cb463369>] __kmem_cache_alloc_node+0x18e/0x720
[<00000000147a3f9c>] kmalloc_node_trace+0x2a/0x130
[<000000004e107011>] io_wq_create+0x7b9/0xdc0
[<00000000c38b2018>] io_uring_alloc_task_context+0x31e/0x59d
[<00000000867399da>] __io_uring_add_tctx_node.cold+0x19/0x1ba
[<000000007e0e7a79>] io_uring_setup.cold+0x1b80/0x1dce
[<00000000b545e9f6>] __x64_sys_io_uring_setup+0x5d/0x80
[<000000008a8a7508>] do_syscall_64+0x5d/0x90
[<000000004ac08bec>] entry_SYSCALL_64_after_hwframe+0x63/0xcd |
| In the Linux kernel, the following vulnerability has been resolved:
ftrace: Fix recursive locking direct_mutex in ftrace_modify_direct_caller
Naveen reported recursive locking of direct_mutex with sample
ftrace-direct-modify.ko:
[ 74.762406] WARNING: possible recursive locking detected
[ 74.762887] 6.0.0-rc6+ #33 Not tainted
[ 74.763216] --------------------------------------------
[ 74.763672] event-sample-fn/1084 is trying to acquire lock:
[ 74.764152] ffffffff86c9d6b0 (direct_mutex){+.+.}-{3:3}, at: \
register_ftrace_function+0x1f/0x180
[ 74.764922]
[ 74.764922] but task is already holding lock:
[ 74.765421] ffffffff86c9d6b0 (direct_mutex){+.+.}-{3:3}, at: \
modify_ftrace_direct+0x34/0x1f0
[ 74.766142]
[ 74.766142] other info that might help us debug this:
[ 74.766701] Possible unsafe locking scenario:
[ 74.766701]
[ 74.767216] CPU0
[ 74.767437] ----
[ 74.767656] lock(direct_mutex);
[ 74.767952] lock(direct_mutex);
[ 74.768245]
[ 74.768245] *** DEADLOCK ***
[ 74.768245]
[ 74.768750] May be due to missing lock nesting notation
[ 74.768750]
[ 74.769332] 1 lock held by event-sample-fn/1084:
[ 74.769731] #0: ffffffff86c9d6b0 (direct_mutex){+.+.}-{3:3}, at: \
modify_ftrace_direct+0x34/0x1f0
[ 74.770496]
[ 74.770496] stack backtrace:
[ 74.770884] CPU: 4 PID: 1084 Comm: event-sample-fn Not tainted ...
[ 74.771498] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), ...
[ 74.772474] Call Trace:
[ 74.772696] <TASK>
[ 74.772896] dump_stack_lvl+0x44/0x5b
[ 74.773223] __lock_acquire.cold.74+0xac/0x2b7
[ 74.773616] lock_acquire+0xd2/0x310
[ 74.773936] ? register_ftrace_function+0x1f/0x180
[ 74.774357] ? lock_is_held_type+0xd8/0x130
[ 74.774744] ? my_tramp2+0x11/0x11 [ftrace_direct_modify]
[ 74.775213] __mutex_lock+0x99/0x1010
[ 74.775536] ? register_ftrace_function+0x1f/0x180
[ 74.775954] ? slab_free_freelist_hook.isra.43+0x115/0x160
[ 74.776424] ? ftrace_set_hash+0x195/0x220
[ 74.776779] ? register_ftrace_function+0x1f/0x180
[ 74.777194] ? kfree+0x3e1/0x440
[ 74.777482] ? my_tramp2+0x11/0x11 [ftrace_direct_modify]
[ 74.777941] ? __schedule+0xb40/0xb40
[ 74.778258] ? register_ftrace_function+0x1f/0x180
[ 74.778672] ? my_tramp1+0xf/0xf [ftrace_direct_modify]
[ 74.779128] register_ftrace_function+0x1f/0x180
[ 74.779527] ? ftrace_set_filter_ip+0x33/0x70
[ 74.779910] ? __schedule+0xb40/0xb40
[ 74.780231] ? my_tramp1+0xf/0xf [ftrace_direct_modify]
[ 74.780678] ? my_tramp2+0x11/0x11 [ftrace_direct_modify]
[ 74.781147] ftrace_modify_direct_caller+0x5b/0x90
[ 74.781563] ? 0xffffffffa0201000
[ 74.781859] ? my_tramp1+0xf/0xf [ftrace_direct_modify]
[ 74.782309] modify_ftrace_direct+0x1b2/0x1f0
[ 74.782690] ? __schedule+0xb40/0xb40
[ 74.783014] ? simple_thread+0x2a/0xb0 [ftrace_direct_modify]
[ 74.783508] ? __schedule+0xb40/0xb40
[ 74.783832] ? my_tramp2+0x11/0x11 [ftrace_direct_modify]
[ 74.784294] simple_thread+0x76/0xb0 [ftrace_direct_modify]
[ 74.784766] kthread+0xf5/0x120
[ 74.785052] ? kthread_complete_and_exit+0x20/0x20
[ 74.785464] ret_from_fork+0x22/0x30
[ 74.785781] </TASK>
Fix this by using register_ftrace_function_nolock in
ftrace_modify_direct_caller. |
| In the Linux kernel, the following vulnerability has been resolved:
riscv: vdso: fix NULL deference in vdso_join_timens() when vfork
Testing tools/testing/selftests/timens/vfork_exec.c got below
kernel log:
[ 6.838454] Unable to handle kernel access to user memory without uaccess routines at virtual address 0000000000000020
[ 6.842255] Oops [#1]
[ 6.842871] Modules linked in:
[ 6.844249] CPU: 1 PID: 64 Comm: vfork_exec Not tainted 6.0.0-rc3-rt15+ #8
[ 6.845861] Hardware name: riscv-virtio,qemu (DT)
[ 6.848009] epc : vdso_join_timens+0xd2/0x110
[ 6.850097] ra : vdso_join_timens+0xd2/0x110
[ 6.851164] epc : ffffffff8000635c ra : ffffffff8000635c sp : ff6000000181fbf0
[ 6.852562] gp : ffffffff80cff648 tp : ff60000000fdb700 t0 : 3030303030303030
[ 6.853852] t1 : 0000000000000030 t2 : 3030303030303030 s0 : ff6000000181fc40
[ 6.854984] s1 : ff60000001e6c000 a0 : 0000000000000010 a1 : ffffffff8005654c
[ 6.856221] a2 : 00000000ffffefff a3 : 0000000000000000 a4 : 0000000000000000
[ 6.858114] a5 : 0000000000000000 a6 : 0000000000000008 a7 : 0000000000000038
[ 6.859484] s2 : ff60000001e6c068 s3 : ff6000000108abb0 s4 : 0000000000000000
[ 6.860751] s5 : 0000000000001000 s6 : ffffffff8089dc40 s7 : ffffffff8089dc38
[ 6.862029] s8 : ffffffff8089dc30 s9 : ff60000000fdbe38 s10: 000000000000005e
[ 6.863304] s11: ffffffff80cc3510 t3 : ffffffff80d1112f t4 : ffffffff80d1112f
[ 6.864565] t5 : ffffffff80d11130 t6 : ff6000000181fa00
[ 6.865561] status: 0000000000000120 badaddr: 0000000000000020 cause: 000000000000000d
[ 6.868046] [<ffffffff8008dc94>] timens_commit+0x38/0x11a
[ 6.869089] [<ffffffff8008dde8>] timens_on_fork+0x72/0xb4
[ 6.870055] [<ffffffff80190096>] begin_new_exec+0x3c6/0x9f0
[ 6.871231] [<ffffffff801d826c>] load_elf_binary+0x628/0x1214
[ 6.872304] [<ffffffff8018ee7a>] bprm_execve+0x1f2/0x4e4
[ 6.873243] [<ffffffff8018f90c>] do_execveat_common+0x16e/0x1ee
[ 6.874258] [<ffffffff8018f9c8>] sys_execve+0x3c/0x48
[ 6.875162] [<ffffffff80003556>] ret_from_syscall+0x0/0x2
[ 6.877484] ---[ end trace 0000000000000000 ]---
This is because the mm->context.vdso_info is NULL in vfork case. From
another side, mm->context.vdso_info either points to vdso info
for RV64 or vdso info for compat, there's no need to bloat riscv's
mm_context_t, we can handle the difference when setup the additional
page for vdso. |
| In the Linux kernel, the following vulnerability has been resolved:
io_uring/rw: defer fsnotify calls to task context
We can't call these off the kiocb completion as that might be off
soft/hard irq context. Defer the calls to when we process the
task_work for this request. That avoids valid complaints like:
stack backtrace:
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 6.0.0-rc6-syzkaller-00321-g105a36f3694e #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 08/26/2022
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_usage_bug kernel/locking/lockdep.c:3961 [inline]
valid_state kernel/locking/lockdep.c:3973 [inline]
mark_lock_irq kernel/locking/lockdep.c:4176 [inline]
mark_lock.part.0.cold+0x18/0xd8 kernel/locking/lockdep.c:4632
mark_lock kernel/locking/lockdep.c:4596 [inline]
mark_usage kernel/locking/lockdep.c:4527 [inline]
__lock_acquire+0x11d9/0x56d0 kernel/locking/lockdep.c:5007
lock_acquire kernel/locking/lockdep.c:5666 [inline]
lock_acquire+0x1ab/0x570 kernel/locking/lockdep.c:5631
__fs_reclaim_acquire mm/page_alloc.c:4674 [inline]
fs_reclaim_acquire+0x115/0x160 mm/page_alloc.c:4688
might_alloc include/linux/sched/mm.h:271 [inline]
slab_pre_alloc_hook mm/slab.h:700 [inline]
slab_alloc mm/slab.c:3278 [inline]
__kmem_cache_alloc_lru mm/slab.c:3471 [inline]
kmem_cache_alloc+0x39/0x520 mm/slab.c:3491
fanotify_alloc_fid_event fs/notify/fanotify/fanotify.c:580 [inline]
fanotify_alloc_event fs/notify/fanotify/fanotify.c:813 [inline]
fanotify_handle_event+0x1130/0x3f40 fs/notify/fanotify/fanotify.c:948
send_to_group fs/notify/fsnotify.c:360 [inline]
fsnotify+0xafb/0x1680 fs/notify/fsnotify.c:570
__fsnotify_parent+0x62f/0xa60 fs/notify/fsnotify.c:230
fsnotify_parent include/linux/fsnotify.h:77 [inline]
fsnotify_file include/linux/fsnotify.h:99 [inline]
fsnotify_access include/linux/fsnotify.h:309 [inline]
__io_complete_rw_common+0x485/0x720 io_uring/rw.c:195
io_complete_rw+0x1a/0x1f0 io_uring/rw.c:228
iomap_dio_complete_work fs/iomap/direct-io.c:144 [inline]
iomap_dio_bio_end_io+0x438/0x5e0 fs/iomap/direct-io.c:178
bio_endio+0x5f9/0x780 block/bio.c:1564
req_bio_endio block/blk-mq.c:695 [inline]
blk_update_request+0x3fc/0x1300 block/blk-mq.c:825
scsi_end_request+0x7a/0x9a0 drivers/scsi/scsi_lib.c:541
scsi_io_completion+0x173/0x1f70 drivers/scsi/scsi_lib.c:971
scsi_complete+0x122/0x3b0 drivers/scsi/scsi_lib.c:1438
blk_complete_reqs+0xad/0xe0 block/blk-mq.c:1022
__do_softirq+0x1d3/0x9c6 kernel/softirq.c:571
invoke_softirq kernel/softirq.c:445 [inline]
__irq_exit_rcu+0x123/0x180 kernel/softirq.c:650
irq_exit_rcu+0x5/0x20 kernel/softirq.c:662
common_interrupt+0xa9/0xc0 arch/x86/kernel/irq.c:240 |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix race when deleting quota root from the dirty cow roots list
When disabling quotas we are deleting the quota root from the list
fs_info->dirty_cowonly_roots without taking the lock that protects it,
which is struct btrfs_fs_info::trans_lock. This unsynchronized list
manipulation may cause chaos if there's another concurrent manipulation
of this list, such as when adding a root to it with
ctree.c:add_root_to_dirty_list().
This can result in all sorts of weird failures caused by a race, such as
the following crash:
[337571.278245] general protection fault, probably for non-canonical address 0xdead000000000108: 0000 [#1] PREEMPT SMP PTI
[337571.278933] CPU: 1 PID: 115447 Comm: btrfs Tainted: G W 6.4.0-rc6-btrfs-next-134+ #1
[337571.279153] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014
[337571.279572] RIP: 0010:commit_cowonly_roots+0x11f/0x250 [btrfs]
[337571.279928] Code: 85 38 06 00 (...)
[337571.280363] RSP: 0018:ffff9f63446efba0 EFLAGS: 00010206
[337571.280582] RAX: ffff942d98ec2638 RBX: ffff9430b82b4c30 RCX: 0000000449e1c000
[337571.280798] RDX: dead000000000100 RSI: ffff9430021e4900 RDI: 0000000000036070
[337571.281015] RBP: ffff942d98ec2000 R08: ffff942d98ec2000 R09: 000000000000015b
[337571.281254] R10: 0000000000000009 R11: 0000000000000001 R12: ffff942fe8fbf600
[337571.281476] R13: ffff942dabe23040 R14: ffff942dabe20800 R15: ffff942d92cf3b48
[337571.281723] FS: 00007f478adb7340(0000) GS:ffff94349fa40000(0000) knlGS:0000000000000000
[337571.281950] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[337571.282184] CR2: 00007f478ab9a3d5 CR3: 000000001e02c001 CR4: 0000000000370ee0
[337571.282416] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[337571.282647] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[337571.282874] Call Trace:
[337571.283101] <TASK>
[337571.283327] ? __die_body+0x1b/0x60
[337571.283570] ? die_addr+0x39/0x60
[337571.283796] ? exc_general_protection+0x22e/0x430
[337571.284022] ? asm_exc_general_protection+0x22/0x30
[337571.284251] ? commit_cowonly_roots+0x11f/0x250 [btrfs]
[337571.284531] btrfs_commit_transaction+0x42e/0xf90 [btrfs]
[337571.284803] ? _raw_spin_unlock+0x15/0x30
[337571.285031] ? release_extent_buffer+0x103/0x130 [btrfs]
[337571.285305] reset_balance_state+0x152/0x1b0 [btrfs]
[337571.285578] btrfs_balance+0xa50/0x11e0 [btrfs]
[337571.285864] ? __kmem_cache_alloc_node+0x14a/0x410
[337571.286086] btrfs_ioctl+0x249a/0x3320 [btrfs]
[337571.286358] ? mod_objcg_state+0xd2/0x360
[337571.286577] ? refill_obj_stock+0xb0/0x160
[337571.286798] ? seq_release+0x25/0x30
[337571.287016] ? __rseq_handle_notify_resume+0x3ba/0x4b0
[337571.287235] ? percpu_counter_add_batch+0x2e/0xa0
[337571.287455] ? __x64_sys_ioctl+0x88/0xc0
[337571.287675] __x64_sys_ioctl+0x88/0xc0
[337571.287901] do_syscall_64+0x38/0x90
[337571.288126] entry_SYSCALL_64_after_hwframe+0x72/0xdc
[337571.288352] RIP: 0033:0x7f478aaffe9b
So fix this by locking struct btrfs_fs_info::trans_lock before deleting
the quota root from that list. |
| In the Linux kernel, the following vulnerability has been resolved:
md/raid1: stop mdx_raid1 thread when raid1 array run failed
fail run raid1 array when we assemble array with the inactive disk only,
but the mdx_raid1 thread were not stop, Even if the associated resources
have been released. it will caused a NULL dereference when we do poweroff.
This causes the following Oops:
[ 287.587787] BUG: kernel NULL pointer dereference, address: 0000000000000070
[ 287.594762] #PF: supervisor read access in kernel mode
[ 287.599912] #PF: error_code(0x0000) - not-present page
[ 287.605061] PGD 0 P4D 0
[ 287.607612] Oops: 0000 [#1] SMP NOPTI
[ 287.611287] CPU: 3 PID: 5265 Comm: md0_raid1 Tainted: G U 5.10.146 #0
[ 287.619029] Hardware name: xxxxxxx/To be filled by O.E.M, BIOS 5.19 06/16/2022
[ 287.626775] RIP: 0010:md_check_recovery+0x57/0x500 [md_mod]
[ 287.632357] Code: fe 01 00 00 48 83 bb 10 03 00 00 00 74 08 48 89 ......
[ 287.651118] RSP: 0018:ffffc90000433d78 EFLAGS: 00010202
[ 287.656347] RAX: 0000000000000000 RBX: ffff888105986800 RCX: 0000000000000000
[ 287.663491] RDX: ffffc90000433bb0 RSI: 00000000ffffefff RDI: ffff888105986800
[ 287.670634] RBP: ffffc90000433da0 R08: 0000000000000000 R09: c0000000ffffefff
[ 287.677771] R10: 0000000000000001 R11: ffffc90000433ba8 R12: ffff888105986800
[ 287.684907] R13: 0000000000000000 R14: fffffffffffffe00 R15: ffff888100b6b500
[ 287.692052] FS: 0000000000000000(0000) GS:ffff888277f80000(0000) knlGS:0000000000000000
[ 287.700149] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 287.705897] CR2: 0000000000000070 CR3: 000000000320a000 CR4: 0000000000350ee0
[ 287.713033] Call Trace:
[ 287.715498] raid1d+0x6c/0xbbb [raid1]
[ 287.719256] ? __schedule+0x1ff/0x760
[ 287.722930] ? schedule+0x3b/0xb0
[ 287.726260] ? schedule_timeout+0x1ed/0x290
[ 287.730456] ? __switch_to+0x11f/0x400
[ 287.734219] md_thread+0xe9/0x140 [md_mod]
[ 287.738328] ? md_thread+0xe9/0x140 [md_mod]
[ 287.742601] ? wait_woken+0x80/0x80
[ 287.746097] ? md_register_thread+0xe0/0xe0 [md_mod]
[ 287.751064] kthread+0x11a/0x140
[ 287.754300] ? kthread_park+0x90/0x90
[ 287.757974] ret_from_fork+0x1f/0x30
In fact, when raid1 array run fail, we need to do
md_unregister_thread() before raid1_free(). |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: akcipher - default implementation for setting a private key
Changes from v1:
* removed the default implementation from set_pub_key: it is assumed that
an implementation must always have this callback defined as there are
no use case for an algorithm, which doesn't need a public key
Many akcipher implementations (like ECDSA) support only signature
verifications, so they don't have all callbacks defined.
Commit 78a0324f4a53 ("crypto: akcipher - default implementations for
request callbacks") introduced default callbacks for sign/verify
operations, which just return an error code.
However, these are not enough, because before calling sign the caller would
likely call set_priv_key first on the instantiated transform (as the
in-kernel testmgr does). This function does not have a default stub, so the
kernel crashes, when trying to set a private key on an akcipher, which
doesn't support signature generation.
I've noticed this, when trying to add a KAT vector for ECDSA signature to
the testmgr.
With this patch the testmgr returns an error in dmesg (as it should)
instead of crashing the kernel NULL ptr dereference. |
| In the Linux kernel, the following vulnerability has been resolved:
netdevsim: fix memory leak in nsim_bus_dev_new()
If device_register() failed in nsim_bus_dev_new(), the value of reference
in nsim_bus_dev->dev is 1. obj->name in nsim_bus_dev->dev will not be
released.
unreferenced object 0xffff88810352c480 (size 16):
comm "echo", pid 5691, jiffies 4294945921 (age 133.270s)
hex dump (first 16 bytes):
6e 65 74 64 65 76 73 69 6d 31 00 00 00 00 00 00 netdevsim1......
backtrace:
[<000000005e2e5e26>] __kmalloc_node_track_caller+0x3a/0xb0
[<0000000094ca4fc8>] kvasprintf+0xc3/0x160
[<00000000aad09bcc>] kvasprintf_const+0x55/0x180
[<000000009bac868d>] kobject_set_name_vargs+0x56/0x150
[<000000007c1a5d70>] dev_set_name+0xbb/0xf0
[<00000000ad0d126b>] device_add+0x1f8/0x1cb0
[<00000000c222ae24>] new_device_store+0x3b6/0x5e0
[<0000000043593421>] bus_attr_store+0x72/0xa0
[<00000000cbb1833a>] sysfs_kf_write+0x106/0x160
[<00000000d0dedb8a>] kernfs_fop_write_iter+0x3a8/0x5a0
[<00000000770b66e2>] vfs_write+0x8f0/0xc80
[<0000000078bb39be>] ksys_write+0x106/0x210
[<00000000005e55a4>] do_syscall_64+0x35/0x80
[<00000000eaa40bbc>] entry_SYSCALL_64_after_hwframe+0x46/0xb0 |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: Fix type of second parameter in odn_edit_dpm_table() callback
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed. A
proposed warning in clang aims to catch these at compile time, which
reveals:
drivers/gpu/drm/amd/amdgpu/../pm/swsmu/amdgpu_smu.c:3008:29: error: incompatible function pointer types initializing 'int (*)(void *, uint32_t, long *, uint32_t)' (aka 'int (*)(void *, unsigned int, long *, unsigned int)') with an expression of type 'int (void *, enum PP_OD_DPM_TABLE_COMMAND, long *, uint32_t)' (aka 'int (void *, enum PP_OD_DPM_TABLE_COMMAND, long *, unsigned int)') [-Werror,-Wincompatible-function-pointer-types-strict]
.odn_edit_dpm_table = smu_od_edit_dpm_table,
^~~~~~~~~~~~~~~~~~~~~
1 error generated.
There are only two implementations of ->odn_edit_dpm_table() in 'struct
amd_pm_funcs': smu_od_edit_dpm_table() and pp_odn_edit_dpm_table(). One
has a second parameter type of 'enum PP_OD_DPM_TABLE_COMMAND' and the
other uses 'u32'. Ultimately, smu_od_edit_dpm_table() calls
->od_edit_dpm_table() from 'struct pptable_funcs' and
pp_odn_edit_dpm_table() calls ->odn_edit_dpm_table() from 'struct
pp_hwmgr_func', which both have a second parameter type of 'enum
PP_OD_DPM_TABLE_COMMAND'.
Update the type parameter in both the prototype in 'struct amd_pm_funcs'
and pp_odn_edit_dpm_table() to 'enum PP_OD_DPM_TABLE_COMMAND', which
cleans up the warning. |
| In the Linux kernel, the following vulnerability has been resolved:
vdpa: Add queue index attr to vdpa_nl_policy for nlattr length check
The vdpa_nl_policy structure is used to validate the nlattr when parsing
the incoming nlmsg. It will ensure the attribute being described produces
a valid nlattr pointer in info->attrs before entering into each handler
in vdpa_nl_ops.
That is to say, the missing part in vdpa_nl_policy may lead to illegal
nlattr after parsing, which could lead to OOB read just like CVE-2023-3773.
This patch adds the missing nla_policy for vdpa queue index attr to avoid
such bugs. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: ipr: Fix WARNING in ipr_init()
ipr_init() will not call unregister_reboot_notifier() when
pci_register_driver() fails, which causes a WARNING. Call
unregister_reboot_notifier() when pci_register_driver() fails.
notifier callback ipr_halt [ipr] already registered
WARNING: CPU: 3 PID: 299 at kernel/notifier.c:29
notifier_chain_register+0x16d/0x230
Modules linked in: ipr(+) xhci_pci_renesas xhci_hcd ehci_hcd usbcore
led_class gpu_sched drm_buddy video wmi drm_ttm_helper ttm
drm_display_helper drm_kms_helper drm drm_panel_orientation_quirks
agpgart cfbft
CPU: 3 PID: 299 Comm: modprobe Tainted: G W
6.1.0-rc1-00190-g39508d23b672-dirty #332
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
rel-1.15.0-0-g2dd4b9b3f840-prebuilt.qemu.org 04/01/2014
RIP: 0010:notifier_chain_register+0x16d/0x230
Call Trace:
<TASK>
__blocking_notifier_chain_register+0x73/0xb0
ipr_init+0x30/0x1000 [ipr]
do_one_initcall+0xdb/0x480
do_init_module+0x1cf/0x680
load_module+0x6a50/0x70a0
__do_sys_finit_module+0x12f/0x1c0
do_syscall_64+0x3f/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd |
| In the Linux kernel, the following vulnerability has been resolved:
opp: Fix use-after-free in lazy_opp_tables after probe deferral
When dev_pm_opp_of_find_icc_paths() in _allocate_opp_table() returns
-EPROBE_DEFER, the opp_table is freed again, to wait until all the
interconnect paths are available.
However, if the OPP table is using required-opps then it may already
have been added to the global lazy_opp_tables list. The error path
does not remove the opp_table from the list again.
This can cause crashes later when the provider of the required-opps
is added, since we will iterate over OPP tables that have already been
freed. E.g.:
Unable to handle kernel NULL pointer dereference when read
CPU: 0 PID: 7 Comm: kworker/0:0 Not tainted 6.4.0-rc3
PC is at _of_add_opp_table_v2 (include/linux/of.h:949
drivers/opp/of.c:98 drivers/opp/of.c:344 drivers/opp/of.c:404
drivers/opp/of.c:1032) -> lazy_link_required_opp_table()
Fix this by calling _of_clear_opp_table() to remove the opp_table from
the list and clear other allocated resources. While at it, also add the
missing mutex_destroy() calls in the error path. |
